• 0577-63660008
     
    減速電機故障原因與措施
     
    故障
    Malfunction
    原因
    Causes
    措施
    Measures
    在減速機的緊固件處有大的噪聲
    High noise at tightening parts
    緊固件松動了
    Loose of tightening parts
    將螺栓/螺母擰緊到規定的扭矩。更換損壞了的螺栓/螺母。
    Tighten nut bolt to correct state Replace damaged nut/bolt
    減速機的噪聲變化
    Changing noise
    齒輪的輪齒發生了損壞
    Teeth of gears get damaged
    和客戶服務部聯系。檢查所有零件上的齒,更換損壞了的零件。
    Consult after-sales department
    Check teeth of gears and replace damaged one.
    軸承間隙過大
    Clearance of bearings too big
    和售后服務部聯系。
    調整軸承的間隙。
    Consult after-sales department
    Adjust the clearance of bearings
    軸承損壞
    Bearings get damaged
    和客戶服務部聯系。
    更換損壞的軸承。
    Consult after-sales department
    Replace damaged bearings
    軸承溫度升高
    Bearing temperature rise
    箱體里面的油面過高或過低
    Oillevel is too high or low
    在室溫下檢查油面的高度并按需加油。
    Check oil level at room temperature and add on reduce oil
    油過于陳舊
    Oil is used too long
    和售后服務部聯系。
    檢查上次換油的時間。
    Consult after-sales department.
    Check the date that oil be replaced last time.
    油泵的機械故障
    Malfunction of oil pump
    和售后服務部聯系。
    檢查油泵的工作是否正常,修理或換新的油泵。
    Consult after-sales department.
    Check if pump works normally,repair or replace it.
    軸承損壞
    Bearing damage
    和售后服務部聯系。
    -查閱操作人員在振動測量中所獲得的數據。
    -檢查并按需要換軸承。
    Consult after-sales department.
    -Look up the date about vibration.
    -Check and replace it on request.
    工作溫度過高
    Working temperature too high
    箱體里面的油面過高
    Oil level is too high
    檢查油面的高度,如果有必要的話,調整。
    Check oil level,and adjust if necessary.
    油過于陳舊
    Oil is used too long
    和售后服務部聯系。
    檢查上一次換油的時間,如果有必要的話就更換。
    Consult after-sales department.
    Check the date that oil was replaced last time,
    replace it if necessary
    油受到嚴重污染
    Oil is pollucted seriously
    和售后服務部聯系
    -換油。
    Consult after-sales department.
    -Replace oil.
    在配備了潤滑油冷卻系統的減速機上:冷卻劑的流量過低或者過高
    Flux of cooling material is too high or low
    全面調節進口和出口管道的閥門。
    檢查水冷裝置的自由流量。
    Adjust entrance and exit valves.
    Check the flux of water cooling devices.
    通過水冷裝置的油流過低,其原因是:濾油器嚴重堵塞
    Oil flux through water cooling devices is too low
    清理濾油器
    Clean oil filter
    油泵的機械故障
    油泵損壞
    Malfunction of oil pump
    Oil pump damage
    和售后服務部聯系。
    -檢查油泵的功能是否正常。
    -修理或者換新。
    Consult after-sales department.
    -Check of oil pump works normally.
    -Repair or replace it.
    在配備了風扇的減速機上:風扇罩的空氣入口和/或箱體嚴重污染
    Entrance of fan shield and housing polluted seriously
    清理風扇罩和箱體
    Cleanse fan shield and housing.
    配備了冷卻螺旋管的減速機:冷卻螺旋管里面結垢
    Redsidues in cooling coil
    和售后服務部聯系。
    -清理或者更換螺旋管。
    Consult after-sales department.
    -Claen or replace cooling coil.
    軸承處的振幅升高
    Swing at bearing higher
    軸承損壞
    Bearing is damaged
    和售后服務部聯系。
    -檢查并按需更換軸承。
    Consult after-sales department
    -Check and replace bearing.
    齒輪損壞
    Gear is damaged
    和售后服務部聯系。
    -檢查并按需更換齒輪。
    Consult after-sales department.
    -Check and replaces gears.
    止回裝置的溫度過高
    止回功能的失效
    Temperature of anti-backstop too high and it becomes malfunction
    止回裝置損壞
    Anti-backstop becomes malfunction
    和售后服務部聯系。
    -檢查并按需更換止回裝置。
    Consult after-sales department.
    -Replace anti-backstop
    減速機漏油
    Oil-leak of gear unit
    箱體蓋或者聯接處的密封不良
    Sealing at cover and connection not in good state
    檢查密封和連接處,如果必要的話,更換新的。將連接處密封好。
    Check air-proof and connection part,replace them if necessary,and seal up connection part.
    徑向軸封失效
    Shaft seal is malfunction
    和售后服務部聯系。
    -換新的徑向密封環。
    Consult after-sales department.
    油中有水
    Water in oil
    油中有雜物
    Mixer in oil
    用試管檢查油的狀態是否有水分存在。
    實驗室分析油.
    Classify if there is water in oil by using tube.
    Analyse oil in laboratory.
    潤滑油冷卻器或者冷卻螺旋管失效。
    Cooling coil is of mal-fanction
    和售后服務部聯系。
    -找出并修理泄漏之處。
    -更換冷卻器或者螺旋管。
    Consult after-sales department.
    -Find out and repair leakage place.
    -replace cooling coil
    減速機受到機器間通風過來的涼空氣而產生凝露
    Cool air will cause water drop in gear unit.
    用合適的保溫材料將減速機保護起來。
    關閉空氣的出口或者在結構上改變其方向。
    Shelter gear units with proper
    注:對于客戶自己無法排除的故障請和我公司售后服務部聯系。
    Note: Please consult after-sales department, if malfunction can not be removed by consumers tehmselves.
     
    0

    在線
    客服

    客服
    熱線

    0577-63660008 63660088
    7*24小時客服服務熱線

    關注
    微信

    關注官方微信
    頂部

    Copyright ?2018 REDSUN TIMES GROUP All Right Reserved

    浙江瑞德森機械有限公司 版權所有

    全國統一服務熱線

    0577-63660008

    白白se在线发布视频